before you start

assembly manual

 

We offer magnetic shift paddles for many cars, but the installation instructions are generally common:

1. Disconnect the car battery (-)

2. Demount and unplug airbag

3. Unplug and screw out OEM shifters

4. Screw in and plug in magnetic paddle shifters

5. Plug and place the airbag

6. Reconnect the Car Battery (-)

Detailed instruction dedicated to each car are avaible below: Porsche, Hyundai, BMW/Toyota

Power Paddles Karol Krzempek accepts no liability for damages resulting from installation errors, bad operation, or not getting acquainted.

safety disclaimer

Our products are made with the utmost care and attention to detail and have been tested in many extreme conditions. However, they should only be used on the track, under controlled conditions, and for their intended purpose.

Power Paddles are created by professionals for professionals.
Be aware that our products should only be used at the track with high safety standards.

Porsche

Instalation time: 20 minutes

Difficulty Level: Medium

Tooling needed:

  • T55 Torx wrench
  • T20 Torx wrench
  • 10 mm socket wrench
  • Flat screwdriver (medium)

1. Disconnect the car battery (-)

Use the 10 mm wrench to disconnect the negative terminal and insulate it to prevent accidental contact.

2. Demount and unplug airbag

Insert a medium flathead screwdriver into the two access points on the bottom of the steering wheel to release the spring clips. Gently pull out the airbag module and unplug the electrical connectors.

3. Remove steering wheel

Use the T55 wrench to unscrew the steering wheel bolt. Disconnect any remaining connectors and carefully pull out the steering wheel.

IMPORTANT: Mark the steering wheel’s position on the spline to ensure accurate reinstallation.

4. Remove OEM Shifters

Use the T20 wrench to unscrew and remove the OEM shifters, taking care with the plugs.

5. Install Magnetic Paddle Shifters

Plug in and attach the magnetic paddle shifters, securing them with the original screws using the T20 wrench.

6. Reassemble Steering Wheel

Align and install the steering wheel on the spline, reconnecting all plugs. Tighten the wheel using the T55 wrench.

7. Attach Airbag

Reconnect the airbag connectors and press the airbag firmly into the steering wheel.

8. Reconnect the Car Battery (-)

Reconnect the battery, securing the terminal with the 10 mm wrench.

Hyundai

Instalation time: 20 minutes

Difficulty Level: Medium

Tooling needed:

  • 2.5 mm allen key
  • 10 mm socket wrench
  • Flat screwdriver (medium)
  • Flat screwdriver (small)
  • Cross screwdriver (medium)

1. Disconnect the car battery (-)

Use the 10 mm wrench to disconnect the negative terminal and insulate it to prevent accidental contact.

2. Demount and unplug airbag

Insert a small flathead screwdriver into the two access points on the back of the steering wheel to release the spring clips. Gently pull out the airbag module and unplug the electrical connectors.

3. Remove OEM Shifters

Use the cross screwdriver to unscrew and remove the OEM shifters, taking care with the plugs.

NOTE: To disconnect the original plugs, pry them out with a small screwdriver.

4. Install Magnetic Paddle Shifters

Plug in and attach the magnetic paddle shifters, securing them with the new screws using the 2.5 mm allen key.

5. Attach Airbag

Reconnect the airbag connectors and press the airbag firmly into the steering wheel.

6. Reconnect the Car Battery (-)

Reconnect the battery, securing the terminal with the 10 mm wrench.

BMW/Toyota

Instalation time: 20 minutes

Difficulty Level: Medium

Tooling needed:

  • 2.5 mm allen key
  • T20 torx wrench
  • 10 mm socket wrench
  • Flat screwdriver (medium)
  • Flat screwdriver (small)

1. Disconnect the car battery (-)

Use the 10 mm wrench to disconnect the negative terminal and insulate it to prevent accidental contact.

2. Demount and unplug airbag

Insert a medium flathead screwdriver into the two access points on the bottom/side of the steering wheel to release the spring clips. Gently pull out the airbag module and unplug the electrical connectors.

3. Remove OEM Shifters

Use T20 torx wrench to unplug and remove the OEM shifters, taking care with the plugs.

NOTE: To disconnect the original plugs, pry them out with a small screwdriver.

4. Install Magnetic Paddle Shifters

Plug in and attach the magnetic paddle shifters, securing them with the new screws using the 2.5 mm allen key.

5. Attach Airbag

Reconnect the airbag connectors and press the airbag firmly into the steering wheel.

6. Reconnect the Car Battery (-)

Reconnect the battery, securing the terminal with the 10 mm wrench.